BIGTREETECH-TouchScreenFirmware

support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1, TFT43, TFT50, TFT70 (by bigtreetech)
C

BIGTREETECH-TouchScreenFirmware Alternatives

Similar projects and alternatives to BIGTREETECH-TouchScreenFirmware
  • GitHub repo BIQU-B1

  • GitHub repo Marlin

    Optimized firmware for RepRap 3D printers based on the Arduino platform. (by bigtreetech)

  • Scout

    Get performance insights in less than 4 minutes. Scout APM uses tracing logic that ties bottlenecks to source code so you know the exact line of code causing performance issues and can get back to building a great product faster.

NOTE: The number of mentions on this list indicates mentions on common posts. Hence, a higher number means a better BIGTREETECH-TouchScreenFirmware alternative or higher similarity.

Posts

Posts where BIGTREETECH-TouchScreenFirmware has been mentioned. We have used some of these posts to build our list of alternatives and similar projects - the last one was on 2021-01-15.
  • TFT35 v3 (e3) Blank after Firmware update.
  • Ender 3 Pro + SKR Mini e3 v2 + TFT35 + OctoPrint
    reddit.com/r/ender3 | 2021-02-23
    ref: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/issues/281
  • Mosquito Magnum Compatibility With Bondtech Ddx
    After a little searching I found this: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/discussions/1567 where they talk about needing to recompile the whole touchscreen firmware to update hardcoded limits. Also can you describe exactly what happens when you try to switch to marlin mode? is it dropping any error codes, or just crashing?
  • TFT35 3.0 touch screen doesn't work after firmware upgrade
  • Wtf are wrong with my walls
    reddit.com/r/ender3 | 2021-01-24
    The GitHub repo had changed to be https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware and I built the firmware using vscode. Looks like maybe entrusting shuffled around in GitHub this fall. Probably worth taking a peek
  • New Skr Mini E3 V2 And Tft35 Bednozzle Temp
  • Only one axis mid-print. After updating firmware, my printer only goes along the Y axis (side to side) after a few layers. Any thoughts? I’ve tried a few models and am getting the same results.
    I used this for the screen firmware.
  • where can i get uncompiled b1 firmware
    Motherboard/Marlin: https://github.com/bigtreetech/Marlin/tree/B1-2.0.5.3 Touchscreen: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware
  • Bltouch Installed And Ready To Go
    The TFT Firmware: Did i understand it correctly: You are using https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware?
  • TFT35 display keeps restarting. I have a SKR Mini E3 V2.0. It eventually starts but it happens everytime I start the printer. Help will be greatly appreciated!
    https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware#update-tft-firmware
  • TFT35-E3 V3.0 Touch Screen Displaying Nonsense

Stats

Basic BIGTREETECH-TouchScreenFirmware repo stats
5
590
9.3
1 day ago

bigtreetech/BIGTREETECH-TouchScreenFirmware is an open source project licensed under GNU General Public License v3.0 only which is an OSI approved license.