zerotier-openwrt
KlipperWrt
Our great sponsors
zerotier-openwrt | KlipperWrt | |
---|---|---|
12 | 7 | |
636 | 168 | |
- | - | |
4.0 | 0.0 | |
6 months ago | over 1 year ago | |
Shell | Shell | |
- | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
zerotier-openwrt
-
ZeroTier to route between networks
Hi, any chance you could be a bit clearer with this? I'm already running zerotier client on the 2nd network router (the 4G router which runs OpenWRT), and I've set it up as per the wiki instructions I linked in my initial post https://github.com/mwarning/zerotier-openwrt/wiki . On which device are you talking about virtual NIC settings?
-
How to implement simple remote admin for few OpenWrt routers?
ZeroTier - seems more complicated than n2n, but has an OpenWrt package
-
Can I have this with Zerotier?
https://github.com/mwarning/zerotier-openwrt/wiki Towards the end it covers routing into your LAN
- Using VPN inside ZeroTier tunnel
- DHCP packet received on wlan0 which has no address
-
ZeroTier on OpenWRT router
I followed this guide to setup ZeroTier on my OpenWRT router. Everything works fine except for the fact that my ZeroTier nodes? are not using my OpenWRT router connection as gateway to Internet.
-
no internet with zerotier
i know this question probably belongs in the zerotier subreddit but there are way more people in this sub so i figured at least 1 other person here knows how to solve this. so i run openwrt (actually helmiwrt) on a raspberry pi 4 and followed these instructions on how to set up zerotier. and this honestly sounds like an awesome thing to have but i can't get it going yet. i got my zt0 interface up and it has an ip address, i made the managed rule within zerotier, did the firewall exception and even selected "allow default route" but soon as i connect my internet goes down. i can however, put in my ip address to my media server and reach that but thats it.
-
"VPN" for home internet
So after setting up Zerotier on OpenWRT (https://github.com/mwarning/zerotier-openwrt/wiki) I was able to connect to my local network and access my nas and my android tv server (don't ask).
-
CGNAT access to MT1300 Beryl ok via phone but not working on win10 machines.. why?
I have set up a GL-Inet Beryl MT-1300 (latest Firmware) with the zerotier package. I have opened port 9993 and created an interface as per the tutorial on Home · mwarning/zerotier-openwrt Wiki · GitHub
- Home network Bridge
KlipperWrt
-
Trying to get klipper onto creality wifi box
Hey guys, I've been following this tutorial for converting a creality wifi box to run klipper: https://github.com/ihrapsa/KlipperWrt
- Creality Ender 3 v2 Neo modification and upgrade guide
-
Klipper on the CR-10 Smart Pro
On a Laptop, log into the Printers Wifi (It will be named CXSWBox-12345678ABCDEF or similar), the password is "12345678". You will get an IP address via DHCP. The Wifi Boards web interface is reachable at 10.10.10.254 with username "admin" and password "admin". Go to Administration > Upload Firmware. Choose one one of the -factory images at https://github.com/ihrapsa/KlipperWrt/tree/main/Firmware/OpenWrt_snapshot, depending if you want to run fluidd or mainsail (Comparison is here: https://www.youtube.com/watch?v=BHVVcjtWTyA). Upload the image, you will get a message "Not a valid firmware". Go to http://10.10.10.254/adm/system_command.shtml and enter mv /var/tmpFW /media/mmcblk0p1/cxsw_update.tar.bz2 and for the next command reboot. Then wait for a KlipperWrt Wifi to show up. Connect to it, use the static IP 192.168.1.23 with netmask 255.255.255.0. The web interface is available at 192.168.1.1:81.
-
Klipper/Mainsail on android phone
I recall that Android phones are unreliable for Klipper with all of their built in power saving features that will interrupt prints. Any device that runs Linux should be able to run Klipper. A VM on a Mac or PC should be able to do it as long as you can reliably forward the virtual serial port. Running on a router is possible with KlipperWRT. https://github.com/ihrapsa/KlipperWrt
-
Running klipper on a 256mb ram device?
Instructions from Iona Rapsa's Github - https://github.com/ihrapsa/KlipperWrt
-
https://github.com/mriscoc/Marlin_Ender3v2/releases/latest
I followed this guide https://github.com/ihrapsa/KlipperWrt (used the openwrt image compiled by ihrapsa).
-
Installing upgrades right away or setting it up stock first?
I bought an Ender 3 v2 for my son as a birthday a couple of weeks ago, it came with the Creality cloud box (as a free gift). The cloud box was promptly flashed to OpenWrt and Klipper installed using guidance from https://github.com/ihrapsa/KlipperWrt.
What are some alternatives?
luci-theme-argon - Argon is a clean and tidy OpenWrt LuCI theme that allows users to customize their login interface with images or videos. It also supports automatic and manual switching between light and dark modes.
KlipperScreen - GUI for Klipper
OpenWrt-NanoPi-R2S-R4S-Builds - OpenWRT Builds for NanoPi R2S & R4S from official Openwrt source code with minimal set of patches
OpenWrt-Rpi - Raspberry Pi & NanoPi R2S/R4S & G-Dock & x86 OpenWrt Compile Project. (Based on Github Action / Daily Update)
nanopi-openwrt - Openwrt for Nanopi R1S R2S R4S R5S 香橙派 R1 Plus 固件编译 纯净版与大杂烩
OctoWrt - A guide to install Octoprint on the Creality WiFi Box or similar OpenWrt devices
opkg-upgrade - List and install OpenWRT / LEDE opkg upgradable packages
klipper-web-control-docker - Klipper with Moonraker shipped with Fluidd and/or Mainsail
ZeroTier - A Smart Ethernet Switch for Earth
klipper-prusa-mk3s - Structured Klipper config for Prusa MK3s 3D printer
linksys-e8450-openwrt-installer - OpenWrt firmware installer for the Linksys E8450 aka. Belkin RT3200 [Moved to: https://github.com/dangowrt/owrt-ubi-installer]