klipper VS Voron-Trident

There is _a lot_ wrong with Marlin. It is a complex codebase, full with ancient artefacts, litterred with preprocessor ifdefs every 2-3 lines of code, dynamic includes in the middle of CPP files, etc[1]. It's about as unreadable as C++ code gets--well, I guess it's not template metaprogramming.

Klipper by contrast is a breeze to read through[2].

I am very grateful for Marlin, for all of reprap, and everyone who has contributed to it. But saying there is nothing wrong with it is straight up misguided.

[1]: https://github.com/MarlinFirmware/Marlin/blob/bugfix-2.1.x/M...

[2]: https://github.com/Klipper3d/klipper/blob/master/src/lcd_hd4...

That's the cfg from my photo https://github.com/Klipper3d/klipper/blob/master/config/generic-mks-sgenl.cfg Just confuses me more

If you have (like me) problems getting the auto reconnect solution mentioned on klipper https://github.com/Klipper3d/klipper/issues/835 running.

Did you check the printer cfg examples folder? Looks like there are a few BTT octopus cfg in there.

Compare your current printer.cfg with the master example here. https://github.com/Klipper3d/klipper/blob/master/config/printer-creality-ender3-2018.cfg

I found scripts to handle this problem, like this here: https://github.com/Klipper3d/klipper/issues/847

Guys, I hope someone who has it could send me the printer.cfg of the Ender 3 V2 Neo, I found it here on github, but it seems that some things are out and don't work the right way. Thanks!

git clone https://github.com/Klipper3d/klipper.git

I like to use KIAUH to install Klipper on the host. The Klipper documentation has instructions on making and flashing the part that comes on the MCU. And the Voron GitHub has sample configs you can use to get started.

If I can recommend - secure those wires when they exit X chain, else they will break in chains. print this https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Gantry/chain_wire_anchor_3hole_x2.stl put it under the chain end piece and use ziptie to tie wires to it. also, the Y cable bridge has a channel where you can put those wires into it, and secure them with zipties. Do not leave them strained like this.

Any chance you could tuck the wiring of A and B motors to 2020 slot and use slot cover, or few of these clips? https://www.thingiverse.com/thing:2246832 or just stock ziptie anchor points https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl It will look a bit better IMO.

Hello, I am not sure what's going on with your back if the gantry wiring. Can you tuck those wires in 2020 extrusion, and secure those with these little clips or print few of these anchors and use zipties? It will move them out of the way, decreasing risk of them getting caught into something. All wires on flying gantry go to A motor mount wnd then they enter Z chain -> to electronics compartment.

Another one - ziptie your wires where they enter drag chains. You can print one of these and put under drag chain end when plastic part does not have holes for pulling zipties through: https://github.com/VoronDesign/Voron-Trident/tree/main/STLs/Gantry Tie it down on one side, then push wires from other side of the chain, pull them, and try to find some middle point between where they move in chain. Then ziptie it there. This will ensure they are not moving around in chains, which will cause them rubbing, and possibly breaking when they bunch up or tangle.

There's a model for holding Wagos on bed extrusion https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/Z_Assembly/wago_221-412_mount.stl

for the wiring goind from left B motor on gantry, you can tuck the cable in the 2020 extrusion groove and secure it with something like this https://www.thingiverse.com/thing:2246832 This clip from Trident repo https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl is also pretty useful to ziptie wires around the frame, inside electronics compartment for example.

No problem, yeah bad luck that you just ran out of connectors :-) Maybe just print few of these https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl and tie the cables down on the bottom of crossbeam for now.

Looks OK, but I am not sure what's going on with cables on the right side around A motor. Any chance you could tuck them under 2020 profile cover or ziptie them? You can print a few of there https://github.com/VoronDesign/Voron-Trident/blob/main/STLs/ElectronicsBay/cable_frame_anchor_x6.stl or https://www.thingiverse.com/thing:2246832