arduino-esp32 VS esp-idf

You could just buy ready-made ESP32 boards with an OV2640 camera built-in, then customize the example sketch from https://github.com/espressif/arduino-esp32/tree/master/libraries/ESP32/examples/Camera/CameraWebServer to your liking.

Are you perhaps this poster? https://github.com/espressif/arduino-esp32/issues/5250 - asking that poster for the list I just asked for went nowhere and it was auto-closed.

/* * Based on the following examples: * WiFi > WiFiMulti: https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/examples/WiFiMulti/WiFiMulti.ino * WiFi > WiFiScan: https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/examples/WiFiScan/WiFiScan.ino * Complete project details at our blog: https://RandomNerdTutorials.com/ * */ #include #include WiFiMulti wifiMulti; // WiFi connect timeout per AP. Increase when connecting takes longer. const uint32_t connectTimeoutMs = 10000; void setup(){ Serial.begin(115200); delay(10); WiFi.mode(WIFI_STA); // Add list of wifi networks wifiMulti.addAP("ssid_from_AP_1", "your_password_for_AP_1"); wifiMulti.addAP("ssid_from_AP_2", "your_password_for_AP_2"); wifiMulti.addAP("ssid_from_AP_3", "your_password_for_AP_3"); // WiFi.scanNetworks will return the number of networks found int n = WiFi.scanNetworks(); Serial.println("scan done"); if (n == 0) { Serial.println("no networks found"); } else { Serial.print(n); Serial.println(" networks found"); for (int i = 0; i < n; ++i) { // Print SSID and RSSI for each network found Serial.print(i + 1); Serial.print(": "); Serial.print(WiFi.SSID(i)); Serial.print(" ("); Serial.print(WiFi.RSSI(i)); Serial.print(")"); Serial.println((WiFi.encryptionType(i) == WIFI_AUTH_OPEN)?" ":"*"); delay(10); } } // Connect to Wi-Fi using wifiMulti (connects to the SSID with strongest connection) Serial.println("Connecting Wifi..."); if(wifiMulti.run() == WL_CONNECTED) { Serial.println(""); Serial.println("WiFi connected"); Serial.println("IP address: "); Serial.println(WiFi.localIP()); } } void loop(){ //if the connection to the stongest hotstop is lost, it will connect to the next network on the list if (wifiMulti.run(connectTimeoutMs) == WL_CONNECTED) { Serial.print("WiFi connected: "); Serial.print(WiFi.SSID()); Serial.print(" "); Serial.println(WiFi.RSSI()); } else { Serial.println("WiFi not connected!"); } delay(1000); }

I have 2 ESP32-S2-Saolo-1 's on hand. I am trying to do the example Wifi FTM code that can be found at the following repo: https://github.com/espressif/arduino-esp32/tree/master/libraries/WiFi/examples/FTM

That has not been my experience at all as a user. ESPHome is even easier than Arduino and I haven’t touched firmware code in years.

The price makes a huge difference when you have dozens of them operating which is trivial with a decent hydroponics and smarthome setup. I also have a dozen boards just sitting idle ready to be called up to replace a failed one or use for a new project because they’re so cheap.

Not to mention the Arduino core is supported officially by ESP32: https://github.com/espressif/arduino-esp32

Who actually uses Arduino in production? Everyone just uses modules (for ESP32) or rolls their own using the Arduino board as a reference.

They've done a good job of hiding the RTOS from you and making most sketches run fine without porting, but you're still running as a task under the RTOS, yielding between loop() calls[1]. This leads to mysterious timing issues if you aren't aware of it[2]

It doesn't appear that the Arduino core for the Renesas chip is using the RTOS, at least by default -- its main loop is literally doing while (1) { loop(); }, similar to how the AVR core works. [3, 4]

  1. https://github.com/espressif/arduino-esp32/blob/72c41d09538663ebef80d29eb986cd5bc3395c2d/cores/esp32/main.cpp#L45

https://github.com/lewisxhe/esp32-camera-series/issues/11 may interest you - you need all the files in the same dir, not just the .ino by itself

I copied all the libraries from here: https://github.com/espressif/arduino-esp32/tree/master/libraries

For returning to deep sleep from the wake-up stub you can take a look at how it is done in https://github.com/espressif/esp-idf/tree/master/examples/system/deep_sleep_wake_stub

You can find the examples here: https://github.com/espressif/esp-idf/tree/master/examples

I found the spi_lcd_touch example and flashed it, and it seems to run fine with either ili9341 or gc9a01 drivers selected (although both are mirrored, and one has the colours inverted compared to the other - both of which I assume are things I can fix in either driver).

If that's the case: You register a GPIO as event source and make a task waiting for it, that then just performs the I2C-transaction. Follow this example https://github.com/espressif/esp-idf/blob/master/examples/peripherals/gpio/generic_gpio/main/gpio_example_main.c

IDF contains stuff like https://github.com/espressif/esp-idf/blob/master/pytest.ini and https://github.com/espressif/esp-idf/blob/master/tools/ci/idf_pytest/constants.py which are not part of the pytest-embedded package.

ugh.. arduino.

Better to start with ESP-IDF, there's a pretty full featured well documented web server, and a lot more.

https://github.com/espressif/esp-idf/tree/master/examples/pr...

i've looked over the the ble peripheiral example https://github.com/espressif/esp-idf/blob/master/examples/bluetooth/nimble/bleprph/README.md and i see it's using

Hi, I have device ESP32-S3-DevKitM-1 and i want to catch keystrokes from keyboard. I tried using this https://github.com/tanakamasayuki/EspUsbHost and example from espressif https://github.com/espressif/esp-idf/tree/release/v5.1/examples/peripherals/usb/host/hid/main but when i connect keyboard it is just connecting and disconnecting. Can anyone help me with this?