arduino-esp32 VS circuitpython

You could just buy ready-made ESP32 boards with an OV2640 camera built-in, then customize the example sketch from https://github.com/espressif/arduino-esp32/tree/master/libraries/ESP32/examples/Camera/CameraWebServer to your liking.

Are you perhaps this poster? https://github.com/espressif/arduino-esp32/issues/5250 - asking that poster for the list I just asked for went nowhere and it was auto-closed.

/* * Based on the following examples: * WiFi > WiFiMulti: https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/examples/WiFiMulti/WiFiMulti.ino * WiFi > WiFiScan: https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/examples/WiFiScan/WiFiScan.ino * Complete project details at our blog: https://RandomNerdTutorials.com/ * */ #include #include WiFiMulti wifiMulti; // WiFi connect timeout per AP. Increase when connecting takes longer. const uint32_t connectTimeoutMs = 10000; void setup(){ Serial.begin(115200); delay(10); WiFi.mode(WIFI_STA); // Add list of wifi networks wifiMulti.addAP("ssid_from_AP_1", "your_password_for_AP_1"); wifiMulti.addAP("ssid_from_AP_2", "your_password_for_AP_2"); wifiMulti.addAP("ssid_from_AP_3", "your_password_for_AP_3"); // WiFi.scanNetworks will return the number of networks found int n = WiFi.scanNetworks(); Serial.println("scan done"); if (n == 0) { Serial.println("no networks found"); } else { Serial.print(n); Serial.println(" networks found"); for (int i = 0; i < n; ++i) { // Print SSID and RSSI for each network found Serial.print(i + 1); Serial.print(": "); Serial.print(WiFi.SSID(i)); Serial.print(" ("); Serial.print(WiFi.RSSI(i)); Serial.print(")"); Serial.println((WiFi.encryptionType(i) == WIFI_AUTH_OPEN)?" ":"*"); delay(10); } } // Connect to Wi-Fi using wifiMulti (connects to the SSID with strongest connection) Serial.println("Connecting Wifi..."); if(wifiMulti.run() == WL_CONNECTED) { Serial.println(""); Serial.println("WiFi connected"); Serial.println("IP address: "); Serial.println(WiFi.localIP()); } } void loop(){ //if the connection to the stongest hotstop is lost, it will connect to the next network on the list if (wifiMulti.run(connectTimeoutMs) == WL_CONNECTED) { Serial.print("WiFi connected: "); Serial.print(WiFi.SSID()); Serial.print(" "); Serial.println(WiFi.RSSI()); } else { Serial.println("WiFi not connected!"); } delay(1000); }

I have 2 ESP32-S2-Saolo-1 's on hand. I am trying to do the example Wifi FTM code that can be found at the following repo: https://github.com/espressif/arduino-esp32/tree/master/libraries/WiFi/examples/FTM

That has not been my experience at all as a user. ESPHome is even easier than Arduino and I haven’t touched firmware code in years.

The price makes a huge difference when you have dozens of them operating which is trivial with a decent hydroponics and smarthome setup. I also have a dozen boards just sitting idle ready to be called up to replace a failed one or use for a new project because they’re so cheap.

Not to mention the Arduino core is supported officially by ESP32: https://github.com/espressif/arduino-esp32

Who actually uses Arduino in production? Everyone just uses modules (for ESP32) or rolls their own using the Arduino board as a reference.

They've done a good job of hiding the RTOS from you and making most sketches run fine without porting, but you're still running as a task under the RTOS, yielding between loop() calls[1]. This leads to mysterious timing issues if you aren't aware of it[2]

It doesn't appear that the Arduino core for the Renesas chip is using the RTOS, at least by default -- its main loop is literally doing while (1) { loop(); }, similar to how the AVR core works. [3, 4]

  1. https://github.com/espressif/arduino-esp32/blob/72c41d09538663ebef80d29eb986cd5bc3395c2d/cores/esp32/main.cpp#L45

https://github.com/lewisxhe/esp32-camera-series/issues/11 may interest you - you need all the files in the same dir, not just the .ino by itself

I copied all the libraries from here: https://github.com/espressif/arduino-esp32/tree/master/libraries

As another point for those interested, it (to my knowledge) is currently the ONLY implementation of a scoring machine that the firmware for the device is written in Circuit Python. which gives this unit an advantage when it comes to any and all multi tasking that the unit may need to do.

The barrier to entry has never been lower. Last night I prototyped some code in Python on my Mac to talk to a Bluetooth peripheral, and then had ChatGPT translate it to Arduino C++ code for a $5 ESP32 which mostly worked on the first go.

You can even run Python on microcontrollers these days. See Adafruit's https://circuitpython.org for which they publish modules for many (almost all?) of the sensors they sell. The modern microcontroller frameworks hide much of the complexity of Wi-Fi, Bluetooth, filesystems, etc. so you can do complicated things with minimal effort. You can really cobble something together in an afternoon.

The Pico runs CircuitPython and uses Adafruit's HID library to emulate a keyboard. It's also possible to emulate a mouse and a gamepad (there are some experiments for gamepad emulation in experiments).

Asked your question in the adafruit discord and they said there's no HT1632c library for circuit python yet. There is a library for micropython. You can request to have it ported from the Micropython library I linked to by opening a feature request in the Circuit Python Github. That would be your best option for now or attempt to port the library yourself.

Microcontrollers can run Python now https://circuitpython.org/

I'm aware of two versions of Python for microcontrollers. Micro Python and Circuit Python

I tried to look in https://github.com/adafruit/circuitpython/tree/main/shared-bindings at audiocore, audioio, an audiomixer looking for a way to access the sample counter manually but I have no clue what I'm looking at :(

Try CircuitPython 8.0.3. The commit log has a couple networking changes for the Pico. My MQTT client seems to have fewer connection issues though they could be a fluke https://github.com/adafruit/circuitpython/compare/8.0.2...8.0.3