OctoPrint-FirmwareUpdater
SKR-2
Our great sponsors
OctoPrint-FirmwareUpdater | SKR-2 | |
---|---|---|
37 | 68 | |
344 | 191 | |
0.6% | - | |
3.0 | 0.0 | |
3 months ago | over 2 years ago | |
Python | C++ | |
GNU Affero General Public License v3.0 | - |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
OctoPrint-FirmwareUpdater
-
So apparently I have to prove that my build plate is in fact pei coated ffs.
After reading some more seems like you CAN do it, but I was either too scared or didn't know about it in Mid-2021
-
Hi, I’m getting these uneven walls. It is the same diameter in each layer but each layer seems to be different from the next. Does anyone know what the problem is / have suggestions of any guides to follow to fix it?
Firmware Updater Useful for flashing firmware to printer without having to use sd card. Frees up an sd card for me
-
SKR V1.4 Turbo: update firmware w/out SD card?
I have 2 skr 1.4 turbo boards and before I switched to klipper I always updated my firmware using the firmware updater plug in for octoprint. On the github page it guided you through setup for that board family. https://plugins.octoprint.org/plugins/firmwareupdater/
-
*SOLVED* I am trying to use Firmware Updater after following install instructions for marlinbft. It seems to not be recognizing that I have the marlin-binary-protocol package installed. I am still getting "Python marlin-binary-protocol package is not installed" under the prerequisite status area.
I followed the install instructions from this link. I installed the python 3 compatible version of heat shrink.
-
How to update firmware to install CR touch?
Method 3 (Through Octopi) - I installed Anaconda to download the firmware updater for Octopi found here (https://plugins.octoprint.org/plugins/firmwareupdater/) but cannot install it through the command line. I get "python setup.py egg_info did not run successfully.". Tried upgrading pip to no avail.
-
S1 Help
if you have an Raspberry pi you can try https://plugins.octoprint.org/plugins/firmwareupdater/
-
Question about flashing firmware
I'm not sure if this OctoPrint plug-in works with the neptune 2 but it's worth a shot. https://plugins.octoprint.org/plugins/firmwareupdater/
- M600 Filament Swap now possible with the Neptune 3 Pro Firmware v1.1.5
-
Anyway to update firmware on E5 pro without and SD card?
You need a plugin called Firmware Updater.
-
Broke my SD Card reader any way I can still flash firmware using my octoprint?
Only if you already have Binary File Trainsfer setting enabled in Marlin. So you might be stuck since that's not normally enabled. But when it is enabled, it does work. I only update via octoprint anymore. https://github.com/OctoPrint/OctoPrint-FirmwareUpdater/blob/master/doc/marlinbft.md
SKR-2
-
Ender 5 plus
The jumpers are described very well in the manual. https://github.com/bigtreetech/SKR-2/tree/master/Hardware
-
SKR 2 Laser Engraver
If you look at the pin diagram on BigtreeTech's github pages, it will tell you what and where all the pin names and numbers are.
- I'm thinking of trying to externally wire a stepper driver to my failed skr2 board, any help with that would be welcomed.QQQQQQQQQQQQQQQQQQQQ
-
SKR 2 mosfet just blew any idea what could have caused this
Check this out https://github.com/bigtreetech/SKR-2/issues/102
- printer is on but nothing is working
-
Klipper base config for Ender 3
Get a board with more stepper drivers like the SKR 3 or an Octopus or something.
-
SKR 2 not turning on when connected the 24v power supply
I connected just the power supply and not turning on anyway. I find this https://github.com/bigtreetech/SKR-2/issues/144 It seems like it's a known issue lol. I'm turning this crap back to them. I have really bad luck for electronics 🤣
-
Help with skr 2 board, it caught on fire today!
Yes. It replaces the z endstop on the 5+. There is a section on how it should be connected in the user manual. https://github.com/bigtreetech/SKR-2/tree/master/Hardware
- First time user of SKR board, looking for help
-
Any idea why this near fan 1 would burn out like this. also is this still usable?
Have a look at the github for the SKR 2 here. In the hardware folder, they've included pinouts and schematics.
What are some alternatives?
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
klipper - Klipper is a 3d-printer firmware
OctoPrint-APCUPC - An OctoPrint plugin for Raspbian to communicate with an APC UPC via serial
pivpn - The Simplest VPN installer, designed for Raspberry Pi
BIGTREETECH-SKR-E3-Turbo
OctoPrint-FixCBDFirmware - Fixes communication with a broken firmware making its rounds that identifies as "CBD make it"
BIQU-B1
obico-server - Obico is a community-built, open-source smart 3D printing platform used by makers, enthusiasts, and tinkerers around the world.
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]