Marlin
Marlin_Ender3v2
Our great sponsors
| Marlin | Marlin_Ender3v2 | |
|---|---|---|
| 877 | 102 | |
| 2,142 | 12 | |
| - | - | |
| 0.0 | 9.9 | |
| 5 months ago | about 2 years ago | |
| C++ | C++ | |
| GNU General Public License v3.0 only | GNU General Public License v3.0 or later |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
Marlin_Ender3v2
-
ender 3v2 upgraded to sprite pro hitting dual screw gantry
From what I'm reading, mriscoc's firmware appears to be a bit more polished and offers even more features than Jyers. Have a look at their page - https://github.com/mriscoc/Marlin_Ender3v2/releases/latest From what I'm reading you can change the bed dimensions via gcode command and also in the advanced settings menu. I'm going to try this route despite having already downloaded all the software to compile my own jyers firmware..
-
Installation and Configuring for an Ender 3 S1
Download the bin file from here https://github.com/mriscoc/Marlin_Ender3v2/releases/latest.
-
Anybody know whats up with my 3dtouch? Just installed
By any chances are you using the Jyers firmware? Because that firmware works horrible with a lot of probes. Try the Professional Firmware, I never had a probe crashing problem with that one.
-
Why does my z offset keep changing?
Once you tram the bed, are you doing a mesh? I use UBL (Unified Bed Leveling) to do a 15x15 mesh that takes approximately 225 points of readings. If you are using Jyers firmware, which I highly recommend) or Professional firmware by mriscoc, both rimwares based on Marlin but are more rich in features than the base Marlin firmware, you can view the mesh on your display and see where the high/low spots are. The mesh can be saved to your EEPROM and used without having to redo the leveling process all the time. This is, of course, providing that your bed is not shifting and you wait for the bed to cool down before removing the prints so it doesn't mesh of the leveling. I am not sure about the Professional firmware (because I don't use that one) but I do know the Jyers firmware has a bunch of precompiled .bin files for all the boards and for many different configurations.
-
EEPROM and detecting of SD card not working correctly after upgrading to 2.4.7 motherboard
https://github.com/Jyers/Marlin/releases or https://github.com/mriscoc/Marlin_Ender3v2/releases
-
Octprint Levelling report vs UBL on printer
I am using a modified Jyers firmware from here: https://github.com/mriscoc/Marlin_Ender3v2
- Micro-Swiss direct drive install.
- Ungraded the bed leveling springs.
-
How do you save your Z offset settings?
i use https://github.com/mriscoc/Marlin_Ender3v2 and i am very happy with it
- CR-Touch - Mesh values are never saved correctly. Bed leveled but the values change after it homes/creates a new mesh.
What are some alternatives?
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
Ender3V2S1 - This is optimized firmware for Ender3 V2/S1 3D printers.
klipper - Klipper is a 3d-printer firmware
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
KlipperWrt - A guide to install Klipper with fluidd, Mainsail or Duet-Web-Control and webcam stream in OpenWrt. Mainly created around the Creality Wi-Fi box but any OpenWrt running device with similar specs will work just fine.
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
VoronUsers - Voron Community mods
Configurations - Configurations for Marlin Firmware
Marlin - Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin installed. Check with your vendor if you need source code for your specific machine.
OctoPrint-FirmwareUpdater - OctoPrint plugin for flashing pre-compiled firmware images to a 3D printer.