Marlin
FluiddPI
Our great sponsors
Marlin | FluiddPI | |
---|---|---|
877 | 28 | |
2,142 | 294 | |
- | 1.0% | |
0.0 | 3.2 | |
5 months ago | 9 months ago | |
C++ | Shell | |
GNU General Public License v3.0 only | GNU General Public License v3.0 only |
Stars - the number of stars that a project has on GitHub. Growth - month over month growth in stars.
Activity is a relative number indicating how actively a project is being developed. Recent commits have higher weight than older ones.
For example, an activity of 9.0 indicates that a project is amongst the top 10% of the most actively developed projects that we are tracking.
Marlin
-
Bl / 3dtouch guide for Ender 3 v2
https://github.com/jyers/marlin/releases/ - Select E3V2-BLTouch-XxX-v4.2.X-v2.0.1.bin with X being either the amount of probing points or the version of your mainboard.
- What is a good reason I should install Jyers Marlin firmware instead of Marlin's Creality 4.2.7 stock firmware? (BTW I do laser engraving and 3D printing on Ender-3)
- How does the filament sensor work wiring-wise on a 4.2.7 board?
-
Display Firmware error with jyers firmware
Couldn't tell you, but the Jyers firmware hasn't been updated since November 2021 according to the Github page: https://github.com/Jyers/Marlin
-
mcu 'mcu': Unable to connect while trying to setup Klipper over USB and UART
I glued 2 5p DuPont connectors back to back and put a red wire for vcc, a black wire for ground, a yellow wire for tx, and a green wire for rx (the colors are irrelevant, just for making sure the correct pins are connected to the pi) according to this schem: https://github.com/Jyers/Marlin/discussions/814
-
Aquila X2
As it is a Creality board then Jyers might be better or even Mriscoc as it is more up to date.
- Jyers 2.0.1 compiling error - E3 V2
-
Why does z axis only have 2 connections on ender 3 board?
Probably from there: https://github.com/Jyers/Marlin/discussions/814
- Extra thermistor stock board
-
I need help upgrading my ender 3V2
I switched to Klipper long time ago, but even back then Creality FW was trash and Jyers was fw to use, but it's outdated now. I think most people use the "Profesional" fw now. It should not be hard to find guide on YT.
FluiddPI
-
Sonic Pad vs Klipper on Raspberry pi (what’s is missing from sonic pad?)
Use a Pi if you can find one and do the same steps from above or use a pre-built image for the Pi like FluiddPI.
-
First print since installing Klipper
i used fluid 1.6 which can be found here https://github.com/fluidd-core/FluiddPI/releases
- New Ender 3 S1 Pro my initial thoughts after a couple of days with it.
- Need compiled firmware for my 300c slice eng thermistor+ extender 400XL printer.. can’t compile on my pc.
-
Real improvements going to Klipper?
I 'm a noobie to RPi so I installed FluiddPi image on an SD card using Rufus -- need to tinker with anything on the RPi directly -- runs fine so far.
-
I'm not sure what to do next. I have an error saying no moonraker connection
All else fails; start over by downloading the FluiddPi Raspberry Pi image zip file from here. FluiddPi v1.17.0
-
Itttsss aliiive!!! Again. Description in comment
Mainsail looks nicer though... the only reason I went Fluidd over Mainsail is because FluiddPi was an easy route to trying Klipper. It's a Pi image with Klipper, Moonraker, and Fluidd pre-installed
- Is a Rasberry Pi 4 (B) 2gb good enough to install and run kilpper on my Ender 5 Plus?
-
Rate my benchy (100mm/s speed, 2000mm/s^2 accel, 0.2mm layer height, Ender 3 v1)
Yes it would be the optimal way to setup Octoprint or finished Raspberry Images like FluiddPi or MainsailOS Octoprint is the „official“ base for Klipper though personally I never had a need for Octoprint Plug-ins and use FluiddPi since a year. Klipper has also its subreddit /r/Klippers
-
Octoprint using klipper for dummies
You need to get the latest fluiddPi. use this link https://github.com/cadriel/FluiddPI/releases/download/v1.16.2/fluiddpi-rpi-lite-v1.16.2.zip This will download the zip file that contains the Fluidd and Klipper software. Now follow the document and video to create a MicroSD card for the PI. The Pi is where Klipper/ fluidd runs. It does all of the work converting the Gcode and it then controls the printer board. Once you have the SD card created then you need to edit the fluiddpi-wpa-supplicant.txt file to enter your SSID and network password. This should get the Pi on your network. Re-read the instructions and see if this works.
What are some alternatives?
BIGTREETECH-SKR-mini-E3 - BIGTREETECH SKR-mini-E3 motherboard is a ultra-quiet, low-power, high-quality 3D printing machine control board. It is launched by the 3D printing team of Shenzhen BIGTREE technology co., LTD. This board is specially tailored for Ender 3 printer, perfectly replacing the original Ender3 printer motherboard.
mainsail - Mainsail is the popular web interface for managing and controlling 3D printers with Klipper.
klipper - Klipper is a 3d-printer firmware
kiauh - Klipper Installation And Update Helper
Marlin_Ender3v2 - This is an optimized firmware for Ender 3v2 3D printers. [Moved to: https://github.com/mriscoc/Ender3v2]
Brainlet
OctoPrint - OctoPrint is the snappy web interface for your 3D printer!
MainsailOS - This Raspberry Pi distribution for managing Klipper 3D printers with Mainsail provides all you need.
klipper - Klipper is a 3d-printer firmware [Moved to: https://github.com/Klipper3d/klipper]
fluidd - Fluidd, the klipper UI.
VoronUsers - Voron Community mods
SuperSlicer - G-code generator for 3D printers (Prusa, Voron, Creality, etc.)