IRremoteESP8266 VS esphome

I am planning to do this soon(TM).

Probably starting with ESPHome to control my heat pumps over IR.

The remote works but I forget to turn it off when not in one of the rooms, and it can't do smarts like keeping temperatures in desired bounds.

An ESP32 running ESPHome with high power IR LED, a presence sensor, temperature sensor, and some pre-built library to control heat pumps[1]. it looks like it should be fairly simple to implement with Home assistant.

Now if I could only disable the beep from the heat pumps receiving commands.

I would like to do smarter lighting, but the lack of decent smart light switches that support local control and are also licenced for use in AU are a blocker there.

[1] https://github.com/crankyoldgit/IRremoteESP8266/wiki#ir-send...

ThermTerm solves all the problems I've had with these physical controls, while integrating the heat pumps into Home Assistant via MQTT. Additional sensors pipe temperature, humidity and light data, for statistics and automation. Out of the box, ThermTerm supports Mitsubishi's infrared protocol, since that's the system I have. Thanks to integration with IRRemoteESP8266, you can make ThermTerm work with your own heat pumps by writing a few lines of adaptor code.

This library has the IR codes defined for tons of heat pumps. The only thing about node red is that it uses Java to build the UI on the webserver. If your already familiar with Java then no big deal, but it's just one more syntax to learn lol.

I used this library with a D1 mini. I then use this to put in my dashboard There are some examples one is a receiver code that you can get your codes, they also have a lot of ACs codes already. There is also an IRServer example that integrates with MQTT and has some stuff to put in your configuration.yaml so you can get it into HA easily I used this for 6 Samsung ACs, LG Dryer, some basic fans with IR. Samsung is the same each command is like all commands in one on, temp, etc. It has all this built in. I think if you have a IR receiver on your esp board and it will sometimes pick up the commands sent by the regular remote so if someone else uses the dumb remote it will update in HA. It's not perfect but it works pretty well. you can get all in one boards on ali express if you search iresp8255 they have transmitters and receivers.

I have tried https://github.com/Arduino-IRremote/Arduino-IRremote and https://github.com/crankyoldgit/IRremoteESP8266, both cause the same error.

First, try to remove the resistor(i was made an ir remote using the top circuit for ir sender). check the components, maybe one of them are dead. Second, check the gpio and config. Third, maybe the problem is the code. Maybe you should try the original IRRemoteESP8266 library first: You should checkout the original esp8266 ir remote library first: https://github.com/crankyoldgit/IRremoteESP8266 checkout my project: https://github.com/KD-MM2/MHI-AirCon-ESP8266/blob/main/Ver-1_Webserver_IRRemote/TurnOnMitsubishiHeavyAc.ino

I was able to finally read one of my remote codes that my other receiver couldn't with the flipper. I then used this library with a D1 mini.

My AC is fujitsu and I found library to control: https://github.com/crankyoldgit/IRremoteESP8266/blob/master/src/ir_Fujitsu.cpp

If it has a remote you can try to control it with an ESP32 with an extra infrared led. Check if it is supported by this library. Some coding would be needed.

I am using the this library and the irmqtt server example. But one thing I did was use a NPN Bipolar Transistors PN2222. I have one leg of the transistor on ground, one leg on a 220ohm resistor ( I think that's the one I used) to the D4 pin and then the ground of the ir led on the last leg then the + side of the led to the 5v side.

You might want to take a look at https://esphome.io/ for an easy integration of an ESP32/8266 into home Assistant.

You can do this with a $30 Sonoff S31 running ESPHome [0]. Since the Sonoff wall switch can run a ping sensor against your server you could create a watchdog automation right on the S31 to shut off the mains power to the S31 switch and turn back on after X seconds.

There are other ways you could have the S31 do operational checks but ultimately ESPHome is probably an interesting consideration and supported by tons of off the shelf hardware.

[0] https://esphome.io/

They're pretty great and compatible with most things. ESPHome [1] is a great resource for getting ESP32's working nicely with HA and you can find lots of projects using it to learn from.

You'll likely need to do soldering if you want to connect sensors, batteries and the like.

Personally I really like what SEEED Studio [2] does with their ESP32 boards and they have nice docs.

1. https://esphome.io/

Maybe you could set up ESPHome on the ESP32. It might make connecting those components easier, plus a decent web server built in. Then your app can be set up to access data provided by the ESPHome web server.

# # Setting pins for sda and scl will be required until https://github.com/esphome/esphome/pull/2970 is released

Probably an unpopular opinion, but for the simple stuff you may just want to use something like EspHome where you just need to create a yaml file. Once you’re comfortable with that maybe get into something a bit more advanced, but esphome make it a breeze. It integrates with home assistant if you already have that in place as well.

ESPHome

Lithium Titanate batteries. Nothing else is lightweight, safe, currently available, and lasts 20000 cycles.

ESPHome. It's a framework for declaratively building firmware for microcontrollers, based on rules like "This pin is an input with debouncing, when it changes, toggle this".

Contributing to them has probably been the most fun I've had programming in years.

We just need power management, and a C++ implementation of the Native API client. It's so close to being able to replace most of what I'd normally code by hand in Arduino.

https://esphome.io/

RealThunder's fork of FreeCAD: https://github.com/realthunder/FreeCAD

They fix so many issues. Linear patterns can duplicate other linear patterns!

Vorta: It's the best backup technology I've seen. Just an easy guided GUI for Borg, which gives you deduplication. I just wish they let you deduplicate across multiple repositories somehow.

Hi, I saw this PR for C6 & C2 but I didn't find any board config I can use with C2.