Control-Surface VS Arduino-AppleMIDI-Library

I built a midi controller. Rather, I repurposed a Teensy-based virtual analogue synth I made ages back that never worked quite right. I had taken the amp/speaker out to use somewhere else, and it was just sitting in a box. I realized I could just use the Control Surface library (https://github.com/tttapa/Control-Surface) and change it to a midi controller in no time flat, so I did. Now just need to get some time to use it to play with VCV Rack.

I was in a similar boat to you, though I have a lot of experience programming outside of the arduino/midi controller context. I was pretty happy to just use https://github.com/tttapa/Control-Surface as a library to handle connecting an arduino with a pot to my PC as a midi controller. The docs and examples the codebase has were very useful.

Wow, what a pretty project! If you end up expanding this, you might look at the Control-Surface lib; seems like it's made for this kind of thing.

https://github.com/tttapa/Control-Surface

I've been working on this beasty project together with a friend. We did some liveshows back then and decided that we needed some more control gear. But not just a laptop focusing launchpad, we wanted to forget there was even a laptop (or other hardware) attached to this controller, so that all our attention and focus would be on the music and the crowd, and above all: we wanted something that would instantly announce your presence on stage.

I used this library with an Arduino and several multiplexers. It worked very well and was easy to use. https://github.com/tttapa/Control-Surface

Should be fixed in https://github.com/tttapa/Control-Surface/commit/eb7a468a0a73584b93be16d978404b25401ce66f, you can increase the SELECT_LINE_DELAY constant if necessary.

The PCB was an entirely new endeavour for me, but it was essential in making the project footprint as small as possible. Never done any kind of electronics design outside of hobbyist arduino stuff and the initial prototype. I used [KiCAD 6] to design the PCB. KiCAD might be the single greatest GUI-based open-source software I have ever used, its a shame FreeCAD is so far behind it in terms of stability. It is also free and open source. I went with a simple 2 layer design with all through-hole components to keep things as simple as possible so people didnt have to mess around with heat guns or toaster ovens to solder the board. It turned out great. I also elected to use a teensy to do the heavy lifting. Sticking to an arduino platform means its a lot easier for people to contribute to the firmware. It also meant I could use the greatest arduino library ever written, Control Surface. Control surface is what makes it so easy to write the midi logic for the firmware. It is the backbone of the firmware and really is incredible.

I'll post the whole thing in a separate message. I've already modified it a little, because there seems to be a quirk in the rtpMIDI implementation that seems to not send a second MIDI message if two of the same type are sent in sequence in the program. Even a few milliseconds delay between them seems to fix it. Here's the github link to the original.

Changing the order of libraries didn't change anything. BUT with that in mind, I tried disabling one of the libraries I wasn't using at the moment: AppleMIDI. The flashing mostly stopped. It flashed for a few times in the beginning, and then stopped almost completely.

Just a thought, in a future build you could go totally wireless (theoretically) if you use: - an ESP8266 or ESP32 with wireless MIDI and - MIDI mixer on Windows.

Just FYI, network MIDI is a thing and you may want to look into it if you haven't before.

As a bonus, the controller I'm using (ESP-01) also has Wi-Fi, so I added on the AppleMIDI library for receiving wireless MIDI (and sending, too, if I so choose). As a final touch I added VirtuinoCM to switch between 3 modes: - MIDI-response - some generic animations - manual colour control.

This is the sketch that worked for me pretty much out of the box. Mac OS has built-in support for Wi-Fi MIDI, but in Windows you'll need to install rtpMIDI. Once the Arduino sketch is loaded and running, rtpMIDI is installed, and both the computer and ESP32 are connected to the same network, the ESP32 should show up in the rtpMIDI control panel.